General Equipment RIP-R-STRIPPER FCS16 Скачать руководство пользователя страница 23

Страница: 23 / 63

FCS16 RIP-R-STRIPPER

FORM GOM4240301, VERSION 3.1

configuration can result in property damage

and/or personal injury.

DETERMINE THE THREADED STUDS ARE

PROPERLY SEATED AGAINST THE SLIDING

SECTION OF THE OPERATOR HANDLE.

THE ADJUSTABLE SECTION MUST BE

FIRMLY SECURED TIGHT AGAINST THE

F I X E D S E C T I O N O F T H E O P E R AT O R

HANDLE. IMPROPERLY SECURED STUDS

CAN RESULT IN INADVERTENT OPERATOR

H A N D L E

M O V E M E N T

A N D / O R

SEPARATION, RESULTING IN PROPERTY

DAMAGE AND/OR PERSONAL INJURY.

STARTING THE RIP-R-STRIPPER ON THE

JOB SITE.

1) Position the RIP-R-STRIPPER on a flat and level

surface of firm foundation.

2) Install a blade or the ceramic tile ripper attachment

per the procedures as outlined in this manual.

3) Determine that the ON/OFF switch located on the

operator handle is in the OFF position.

UNEXPECTED MACHINE START UP CAN

RESULT IN PROPERTY DAMAGE AND/OR

PERSONAL INJURY.

4) The RIP-R-STRIPPER is designed to operate from a

clean, 15 ampere, 115 VAC, 60 Hz, nominal power

source. A clean power source refers to the amperage

available from the individual electrical circuit selected.

Additional electrical products already utilizing the same

circuit will reduce the available amperage, and can

result in starting and operational difficulties.

Operating the RIP-R-STRIPPER from a power

source of improper voltage and/or amperage

will result in unrepairable damage to the

electric motor and related controls.

5) Providing proper voltage and amperage levels to the

electric motor is essential to obtain maximum

productivity and service life. Low voltage and

amperage levels will cause the motor to overheat. The

motor is equipped with an automatic thermal protection

device that will stop it before major internal damage can

result. After the motor has cooled to an acceptable

temperature level, the switch must be manually

activated to restart. FIGURE 21.

FIGURE 21

6) The RIP-R-STRIPPER utilizes a factory supplied

extension cord equipped with an integral GFI device.

The GFI device is intended to protect both the

operator and electric motor in the event a ground fault

is developed during operation. The extension cord is

37 foot (11 m) long, fabricated from 12 AWG wire and

incorporates a NEMA 5-15P plug and a NEMA L5-15R

twist lock type receptacle. The twist clock feature

allows the extension cord to be pulled by the RIP-R-

STRIPPER without becoming disconnected.

BEFORE USE, PROPERLY INSPECT THE

EXTENSION CORD AND WIRING DEVICES

FOR STRUCTURAL INTEGRITY. DO NOT

UTILIZE A CORD WITH A WORN OR CUT

OUTER JACKET MATERIAL. DO NOT

UTILIZE A CORD WITH EXPOSED INNER

WIRES OR INSULATION MATERIAL. DO NOT

UTILIZE A CORD THAT HAS BEEN

REPAIRED WITH ELECTRICAL TAPE. DO

NOT UTILIZE A CORD WITH A CRACKED

AND/OR DAMAGED GFI CASE. USE OF AN

E X T E N S I O N C O R D O F I M P R O P E R

S T R U C T U R A L I N T E G R I T Y A N D / O R

DAMAGED GFI CAN RESULT IN PROPERTY

DAMAGE AND/OR PERSONAL INJURY.

Содержание RIP-R-STRIPPER FCS16
































































Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды

General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды