General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Страница: 20 / 63

FCS16 RIP-R-STRIPPER
FORM GOM4240301, VERSION 3.1
18
BLADES ARE EXTREMELY SHARP.
CONTACT WITH THE BLADE CAN RESULT
I N P R O P E R T Y D A M A G E A N D / O R
P E R S O N A L I N J U RY. B L A D E S A R E
PROVIDED WITH A PROTECTIVE COVER
OVER THE CUTTING EDGE. EXERCISE
EXTREME CAUTION WHEN REMOVING
AND/OR REINSTALLING THE PROTECTIVE
COVER. STORE THE BLADE WITH THE
P R O T E C T I V E C O V E R P R O P E R LY
INSTALLED TO MINIMIZE THE POTENTIAL
FOR BLADE DAMAGE AND/OR PERSONAL
INJURY.
7) Return the RIP-R-STRIPPER to its normal operating
position.
8) Determine that the ON/OFF switch located on the
operator handle is in the OFF position. If the RIP-R-
STRIPPER is to be used immediately, then reconnect
the extension cord or RIP-R-STRIPPER to the power
source.
UNEXPECTED MACHINE START UP CAN
RESULT IN PROPERTY DAMAGE AND/OR
PERSONAL INJURY.
Operation
OPERATIONAL DISCLAIMER.
THE MANUFACTURER OF THE RIP-R-
STRIPPER MAKES NO WARRANTY OR
GUARANTEE THAT IT IS MERCHANTABLE
AND/OR SUITABLE FOR ANY SPECIFIC JOB
APPLICATION AND THAT IT WILL HAVE THE
CAPABILITY AND POWER REQUIRED TO
REMOVE ANY SPECIFIC COVERING FROM
ANY SPECIFIC WORK SURFACE.
C A L I F O R N I A P R O P O S I T I O N 6 5
DISCLAIMER.
THE DUSTS/BYPRODUCTS FROM THE
C O V E R I N G R E M O V A L P R O C E S S
ASSOCIATED WITH THE OPERATION OF
THE RIP-R-STRIPPER CAN CONTAIN
CHEMICALS KNOWN TO CAUSE CANCER,
B I R T H D E F E C T S , O R O T H E R
REPRODUCTIVE HARM.
I N F O R M AT I O N R E L AT I V E TO M I N I M U M
C O M P O N E N T S TA N D A R D S F O R T H E
OPERATION OF THE RIP-R-STRIPPER.
For operational safety and overall productivity
considerations, it is required that specific RIP-R-
STRIPPER components meet minimum acceptable
operational standards BEFORE utilization:
1) Operator handle be properly mounted to the main
frame, with factory supplied ball-detent type retaining
pins that properly secure the handle to the main frame
while in the work position.
2) The operator handle is equipped with properly fitting
handle grips of sufficient integrity to allow for proper
job function as outlined within this manual. Loose
fitting handle grips or grips without full end caps are not
permitted.
3) An ON/OFF motor switch that allows it to perform its
intended job function as outlined within this manual.
Replace any damaged ON/OFF motor switch with a
factory approved replacement part only.
4) An extension cord and GFI that allows this accessory
to perform its intended job function as outlined within
this manual. Replace any damaged extension cord or
GFI with a factory approved replacement part only.
5) Exciter plate elastomeric rubber mounts which allow
them to perform their intended job function as outlined
within this manual. Do not operate the RIP-R-
STRIPPER without the correct number of exciter plate
elastomeric rubber mounts. Do not operate the RIP-R-
STRIPPER with a damaged and/or improperly secured
rubber mount. Replace any damaged rubber mount
with a factory approved replacement part only.
6) Blade(s) and/or ceramic tile ripper attachment of
proper structural integrity (void of cracks, etc),
straightness, sharpness, etc which are retained by the
proper fasteners. Replace worn or damaged blades,
fasteners and the ceramic tile ripper attachment with a
factory approved replacement part only.