General Equipment RIP-R-STRIPPER FCS16 Скачать руководство пользователя страница 30

Страница: 30 / 63

FCS16 RIP-R-STRIPPER

FORM GOM4240301, VERSION 3.1

5) Typically, adhesive/mastic densities or thickness

change on the job site usually as a result of application

rates on the work surface. This, in turn directly affects

bond densities and thickness. As these factors

change, the blade angle can be adjusted with the Back

Saver™ Blade Control System to help optimize

covering removal rates.

6) Keep the extension cord free and clear the the main

frame area and orbiting blade/ceramic tile ripper

attachment while the RIP-R-STRIPPER is in operation.

Contact with the blade can damage the extension cord

and create a potential electrocution concern. In the

event of damage, replace the extension cord with a

factory approved replacement part only.

KEEP THE EXTENSION CORD FREE AND

CLEAR OF THE MAIN FRAME AND BLADE

AREA WHILE THE RIP-R-STRIPPER IS IN

OPERATION. CONTACT WITH THE MAIN

FRAME AND BLADE AREA CAN RESULT IN

PROPERTY DAMAGE AND/OR PERSONAL

INJURY.

IN THE EVENT THE EXTENSION CORD

BECOMES ENTANGLED ABOUT THE RIP-R-

STRIPPER AND/OR THE OPERATOR, TURN

THE ELECTRIC MOTOR ON/OFF SWITCH TO

T H E O F F P O S I T I O N . FA I L U R E T O

PROPERLY STOP THE RIP-R-STRIPPER IN

THIS OPERATING CONFIGURATION CAN

RESULT IN PROPERTY DAMAGE AND/OR

PERSONAL INJURY. DETERMINE THE

EXTENSION CORD AND GFI ARE IN PROPER

CONDITION TO CONTINUE OPERATION.

REPLACE ANY DAMAGED COMPONENT

W I T H

F A C T O R Y

A P P R O V E D

REPLACEMENT PART ONLY.

DISCONNECT THE EXTENSION CORD FROM

THE RIP-R-STRIPPER WHEN TRAVERSING

U P A N D D O W N S T A I R W AY S . A N

I M P R O P E R LY S T O R E D / C O N N E C T E D

EXTENSION CORD CAN ENTRAP AND/OR

ENTANGLE PERSONNEL, RESULTING IN

PROPERTY DAMAGE AND/OR PERSONAL

INJURY.

7) Scoring blades are available to remove covering

material such as rubber-backed carpet and linoleum

from concrete and wood surfaces. The vertical ends of

the scoring blade are designed to shear the covering

and remove it in various widths as determined by the

overall blade width. FIGURE 30.

FIGURE 30

Do not operate the RIP-R-STRIPPER with

the vertical ends of the scoring blade fac-

ing down toward the work surface. In

configuration, damage to the work surface

can result.

8) Part Number FCS16-1900 Blade can be mounted to

the RIP-R-STRIPPER in the offset configuration to

allow coverings to be removed from under the kick

panel areas of cabinets and other, unaccessible

locations. A stiffener is included with this blade as a

standard accessory and must be mounted whenever

this blade is utilized to minimize blade deflection.

FIGURE 31.

Содержание RIP-R-STRIPPER FCS16
































































Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды

General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды