General Equipment RIP-R-STRIPPER FCS16 Скачать руководство пользователя страница 32

Страница: 32 / 63

FCS16 RIP-R-STRIPPER

FORM GOM4240301, VERSION 3.1

section for additional information.

Sleeve type bearings are self-lubricating and will not

normally require additional lubrication during their

normal service life. Ball type bearings are shielded or

sealed and will not normally require additional

lubrication during their normal service life.

9) Determine that all safety decals and operational

information decals (including the applicable Quik Tips

information) is in proper and readable condition.

Replace any missing or damaged safety decal and/or

information decal with a factory approved replacement

part only.

10) The RIP-R-STRIPPER utilizes antivibration handle

grips on the operator handle to enhance control and

help dampen the forces experienced during the

covering removal process. Determine the handle is

equipped with properly fitting handle grips of sufficient

integrity to allow for proper job function as outlined in

this manual. Loose fitting handle grips or grips without

end caps should be replaced with factory approved

replacement parts only.

DO NOT OPERATE THE RIP-R-STRIPPER

WITHOUT PROPERLY FITTED HANDLE

G R I P S O F S U F F I C I E N T I N T E G R I T Y

INSTALLED ON THE OPERATOR HANDLE.

OPERATING THE RIP-R-STRIPPER WITH

IMPROPER OR NO HANDLE GRIPS CAN

RESULT IN PROPERTY DAMAGE AND/OR

PERSONAL INJURY.

LUBRICATION REQUIREMENTS.

Parts Required:

1 each, standard grease gun filled with one of the

following: ESSO Beacon 325, Shell Alvania #2,

Chevron SRI, or equivalent.

1 each, container of dry film lubricant.

1) Lubricate the caster wheel bearings with a dry film

lubricant only. Dry film lubricants dry immediately upon

contact. Use sparingly. Excess lubricant will attract the

fine grained, powdered materials described and

directly affect bearing service life.

Do not lubricate the caster wheels with any

lubricant other than a dry film type. Grease

and many other liquid type lubricants will

attract foreign material accumulations that

can reduce bearing service life.

2) Zerk

type grease fittings are provided at two

locations:

a) To lubricate the Back Saver™ Blade Control System

jackscrew. Keep the jackscrew properly lubricated with

grease to minimize friction when operating the blade

control lever. Excessive lubrication will attract foreign

material accumulations that can reduce jackscrew ser-

vice life. FIGURE 32.

b) To lubricate the exciter bearing and bearing housing

casting. The exciter utilizes a shielded type ball bear-

ing. The Zerk

fitting provides lubrication for both the

balls and self-aligning feature of the bearing unit. FIG-

URE 33. Grease interval will vary depending upon

machine utilization rates and operating environment

factors. Grease accumulation on the bearing and hous-

ing would indicate excessive lubrication.

Sleeve type bearings utilized for the operator handle

are self-lubricating and will not normally require

additional lubrication during their normal service life.

Ball type bearings are shielded or sealed and will not

normally require additional lubrication during their

normal service life.

FIGURE 32

Содержание RIP-R-STRIPPER FCS16
































































Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды

General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды