Gemini CDS-2000, Руководство по эксплуатации

Страница: 4 / 18

Page 4
INTRODUCTION
Congratulations on purchasing a Gemini CDS-2000 Dual CD Player. This
state of the art professional CD player is backed by a three year warranty,
excluding lasers. One year warranty on CD lasers. Prior to use, we
suggest that you carefully read all the instructions.
CAUTIONS
1. Do not use this CD Player at temperatures below 41°F/5°C or higher
than 95°F/35°C.
2. The apparatus should not be exposed to dripping or splashing, and no
objects filled with liquids such as vases should be placed on the
apparatus.
3. Place the unit in a clean and dry location.
4. Do not place the unit in an unstable location.
5. When disconnecting the power cord from an AC outlet, always grasp it
by the plug. Never pull the power cord.
6. To prevent electric shock, do not remove the cover or the bottom
screws. There are no user serviceable parts inside. Please refer
servicing to a qualified technician.
7. Do not use chemical solvents to clean the unit.
8. Keep the laser pickup clean by keeping the tray closed.
9. Keep this manual in a safe place for future reference.
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5mW
IMPORTANT NOTE
Since the CDS-2000 is a dual CD player, most of the functions and controls
are duplicated on both sides of the CD player. To eliminate confusion and to
make the drawings easier to understand, we will only number the right side
functions and controls. The only controls that are not duplicated are the
ROBO START (1) , POWER (25) switch and the VOLTAGE SELECTOR
SLIDE (27) .
LINE VOLTAGE SELECTION
Model CDS-2000 is a dual voltage unit. It will operate at 115 or 230 volts. To
set the proper voltage follow these steps:
1. Place the head of a screw driver in the center of the VOLTAGE
SELECTOR SLIDE (27) found on the rear panel.
2. Slide the switch left for 115 volts or push the switch right for 230 volts.
3. Do not force or twist the switch. Excessive force may cause damage. If
the switch does not move smoothly, contact a qualified technician.
CONNECTIONS
1. Using the included cable, plug one end into the REMOTE JACK (26) and
the other end into the PLAYER JACK (28) .
2. Plug one end of a set of RCA connectors into each of the LINE OUTPUT
(30) jacks.
3. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are playing the CDS-2000 through a
receiver, you can plug the RCA connectors into the CD or AUX input
jacks on your receiver. If there are no CD or AUX inputs, use any line
level (not phono) inputs.
FUNCTION DESCRIPTIONS
ANTI-SHOCK BUFFER MEMORY : With 12 SECONDS OF ANTI-SHOCK
BUFFER MEMORY , each side of the CD player stores 6 seconds of
future play to ensure that any harsh movement or bumping of the unit
will not interrupt play and play will continue smoothly.
POWER SWITCH : After making sure that the VOLTAGE SELECTOR
SLIDE (27) , found on the rear panel, is properly set, plug the unit in and
press the POWER (25) switch. The unit will turn on. Pushing the
POWER (25) switch a second time will turn the unit off.
DISC TRAY : The DISC TRAY (24) is where the CD is held during loading,
unloading and playback. Pressing the disc tray OPEN/CLOSE (20)
button, will open or close the tray. The DISC TRAY (24) holds both 12
cm and 8 cm CDs. Please note, if the CDS-2000 is in the play mode, the
tray will not open.
OPEN/CLOSE BUTTON : Press the OPEN/CLOSE (20) button to load or
remove a CD from the DISC TRAY (24) .
DISPLAY : The DISPLAY (5) shows the track number, pitch value, single-
auto cue, continue (for continuous play), and 3 different time displays.
These time displays are time elapsed (ELAPSED) on the track, time
remaining on the disc (TOTAL REMAIN) and time remaining on the track
(REMAIN). Time is measured in minutes, seconds and frames.
PLAYBACK DISPLAY : The PLAYBACK DISPLAY (6) displays the time
remaining to play and flashes slowly when the track has 30 seconds
left. The
PLAYBACK DISPLAY (6) flashes quickly when the track has
15 seconds left.
PLAY/PAUSE : Each press of the PLAY/PAUSE (22) button causes the
operation to change from play to pause or from pause back to play.
TRACK SKIP : The TRACK SKIP (19) buttons let you select the
track to play.
SEARCH JOG WHEEL : The SEARCH JOG WHEEL (10) has two
functions. Use the SEARCH JOG WHEEL (10) to make fine adjustments
in PAUSE mode. Use the SEARCH JOG WHEEL (10) to bend the pitch
for precise synchronization in PLAY mode.
SEARCH DIAL : Use the SEARCH DIAL (9) to select the scanning direction
and speed. Turning the dial in the clockwise direction will scan forward
and counter clockwise will scan in reverse. The scanning speed
increases as the dial is turned further.
STOP : The STOP (23) button will end the playing of the CD.
TIME : The TIME (14) button switches the time display between the three
available choices listed under DISPLAY .
CUE 1 and CUE 2 : Use the CUE BUTTONS (14) in setting cue points. See
the CUE INSTRUCTIONS section for more information. In play mode,
pressing a
CUE BUTTON will pause play and bring you to the CUE
POINT when you can then press the play/pause button to play from the
CUE POINT.
SET CUE : Use the SET CUE (11) button to activate the DIRECT ACCESS
BUTTONS to set a CUE POINT. See the CUE INSTRUCTIONS section for
more information.
DIRECT ACCESS BUTTONS : Use the DIRECT ACCESS (2) buttons to
select what track to play and to set a CUE POINT. See the CUE IN-
STRUCTIONS section for more information.
SINGLE-AUTO CUE/CONTINUOUS : Pressing the SINGLE-AUTO CUE/
CONTINUOUS (12) button activates the AUTO CUE FUNCTION. The
AUTO CUE FUNCTION causes the unit to pause at the beginning of
music of the following track and allows you to start play immediately
from the start of music without any blank space (which exists at the
beginning of every track). Pressing the
SINGLE-AUTO CUE/CONTINU-
OUS (12) button a second time activates the CONTINUOUS function
causing the unit to play continuously (after the last track, the unit will
return to the first track of the disc and continue to play). Pressing the
SINGLE-AUTO CUE/CONTINUOUS (12) button a third time deactivates
the CONTINUOUS function.
ROBO START : Press the ROBO START (1) button to activate ROBO
START (the button will blink). Use ROBO START in SINGLE-AUTO CUE
MODE to alternate play between the two sides of the CD player (one
track from one side, then one track from the other side). See the “Robo
Start Instructions” section for further instructions.
PITCH CONTROL : Pushing the PITCH CONTROL (3) activates the pitch
section of the unit (pitch LED glows red). The pitch of the CD will
change according to the position of the
PITCH SLIDE (15) .
PITCH BEND BUTTONS : Pushing the PITCH BEND (4) buttons will
automatically raise or lower the pitch +/- 16% without changing the slide
setting. Releasing the buttons will return the pitch to the slide setting.
You can use this function to match the pitch bend when mixing from one
song to another.