Geist Watchdog 100 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 61

background image

Chapter 3 - Setup

51

© 2017 Geist

GM1118 Watchdog 100 Instruction Manual

SNMP

Simple Network Management Protocol (SNMP) can be used to monitor the unit's
measurements and status, if desired. SNMP v1, v2c and v3 are supported. In addition,
alarm traps can be sent to up to two IP addresses.

Figure 3-29 SNMP Configuration Page

The

SNMP-V1/V2c and SNMP-V3 Service

can be enabled or disabled independently as

desired. The service will normally listen for data-read requests (a.k.a. "GET requests") on

Port

161, which is the usual default for SNMP services; this can also be changed if

desired.

The Management Information Base (MIB) can be downloaded from the unit, if needed, via
the MIB link at the top of the web page. Clicking this link will download a .ZIP archive
containing both the MIB file itself, and a CSV-formatted spreadsheet describing the
available OIDs in a human-readable form to assist you in setting up your SNMP manager
to read data from the unit.

Figure 3-30 SNMP Users Configuration Page

The

Users

section allows you to configure the various Read, Write, and Trap communities

for SNMP services. You can also configure the authentication types and encryption
methods used for the SNMP v3 if desired. Click the Modify icon to change settings.

«
...
49
50
51
52
53
...
»

Содержание Watchdog 100






























































Отзывы:

Нет отзывов

Похожие инструкции для Watchdog 100

SXNP10 - DIGITAL PIANO

Бренд: Panasonic Страницы: 63

Бренд: Keithley Страницы: 49

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: Van Walt Страницы: 12

Бренд: WAGO Страницы: 96

Бренд: PCB Piezotronics Страницы: 15

Бренд: Macnaught Страницы: 8

Бренд: GMC-I Prosys Страницы: 10

Бренд: S&S Northern Страницы: 5

Бренд: Bruker BioSpin Страницы: 76

Бренд: Proteus Страницы: 4

Бренд: Fluke Страницы: 22

FTCI-3/4D15A4P-2LUX-H1141

Бренд: turck Страницы: 2

Superstatic 749

Бренд: Sontex Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: Fluke Страницы: 97

Бренд: TE Connectivity Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды