Geist Watchdog 100 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 61

background image

Watchdog 100 Instruction Manual

58

© 2017 Geist

GM1118 Watchdog 100 Instruction Manual

and the Watchdog 100 still cannot seem to connect to the Exchange server, the account
probably did not properly inherit the new permissions when you enabled them as above.
This tends to happen more often on Exchange servers that have been upgraded since the
account(s) you are trying to use were first created, but can sometimes happen with
accounts when new connectors and plug-ins are added regardless of the Exchange
version. Delete the user account, then create a new one for the monitoring unit to use, and
the new account should inherit the SMTP authentication and mail-relaying permissions
correctly.

If none of the above suggestions succeed in allowing your Geist Watchdog 100 to send
mail through your Exchange server, then you may need to contact Microsoft’s technical
support for further assistance in configuring your Exchange server to allow SMTP emails
to be sent from a 3rd-party, non-Windows device through your network.

Product-Specific Safety Notices

The specific procedural safety precautions relating to this product are stated
below.

General Safety

Safety is a serious matter and all precautions should to taken to guarantee a
safe work and operational environment. General safety precautions must be
observed during all aspects of operation, service, and repair of equipment
described in this document. Failure to comply with the safety warnings,
procedures and guidelines as presented in this document is in violation of the
safety standards of design, manufacture, and intended use of this equipment.

You are responsible for following the safety guidelines and warnings presented
in this document for this equipment. Individuals using or maintaining Geist
product(s) are expected to follow all the noted warnings and safety precautions
necessary for safe operation of the equipment in your environment. Geist
assumes no liability for failure to comply with these requirements.

Live Circuits Safety

DANGER

HAZARDOUS VOLTAGE, CURRENT, AND ENERGY LEVELS
ARE PRESENT IN THIS PRODUCT. POWER SWITCHED
CIRCUITS CAN HAVE HAZARDOUS VOLTAGES PRESENT
EVEN WHEN THE SWITCH IS IN THE OFF POSITION. DO NOT
OPERATE THE PRODUCT WITH ANY COVER PLATE
REMOVED. ALWAYS MAKE SURE THAT PRODUCT IS FULLY
ENCLOSED PRIOR TO USE.

Operating personnel must:

«
...
56
57
58
59
60
...
»

Содержание Watchdog 100






























































Отзывы:

Нет отзывов

Похожие инструкции для Watchdog 100

Бренд: Yamaha Страницы: 2

Бренд: FARMSCAN Страницы: 28

Бренд: Keithley Страницы: 138

Бренд: Facom Страницы: 42

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

Бренд: GARANT Страницы: 368

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Бренд: bentrup Страницы: 9

Бренд: Mic Страницы: 2

Бренд: Olympus Страницы: 2

RP050B-S1/2 Series

Бренд: MST Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды