Geist Watchdog 100 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 61

background image

Watchdog 100 Instruction Manual

20

© 2017 Geist

GM1118 Watchdog 100 Instruction Manual

Chapter 2 - Installation

Pre-Installation

Guidelines

·

If the Watchdog 100 is installed in a cabinet, the ambient temperature of the rack
should be no greater than 80 °C.

·

Install the Watchdog 100 such that the amount of airflow required for safe operation
of equipment is not compromised.

·

Mount the Watchdog 100 so that a hazardous condition is not achieved due to
uneven mechanical loading.

Installation

1. Using appropriate hardware, mount unit at desired location. See next section for

examples.

2. Connect AC power supply to appropriate source, or if using PoE, connect Ethernet

cable to PoE enabled switch port.

3. Connect any external plug and play sensors into the devices RJ-12 ports .

Network Setup

The Watchdog 100 has a default IP address for initial setup and access. Once you have
assigned an IP address, the default IP address will no longer be active. To restore the
default IP address and reset all user-account information, if the user-assigned address or
passwords are lost or forgotten, press and hold the network-reset button located to the
right of the Ethernet port for 15 seconds.

To completely erase ALL of the user settings and restore the unit back to its factory-
default state, disconnect power from the Watchdog 100, then press and hold the network-
reset button while powering up the unit.

The Network page (located under the System Tab) allows you to assign the network
properties manually, or use DHCP to connect to your network.  Access to the unit
requires the IP address to be known.  Use of a static IP or a reserved DHCP is
recommended.  The default address is shown on the front of the unit:

Table 2-1

Default IP Address

IP Address:

192.168.123.123

Subnet Mask:

255.255.255.0

Gateway:

192.168.123.1

«
...
18
19
20
21
22
...
»

Содержание Watchdog 100






























































Отзывы:

Нет отзывов

Похожие инструкции для Watchdog 100

Бренд: ABB Страницы: 8

Бренд: Bacharach Страницы: 87

Acuvim-L Series

Бренд: AccuEnergy Страницы: 83

Bass Master Rockabilly

Бренд: K&K Sound Страницы: 2

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: Kawai Страницы: 8

Бренд: janitza Страницы: 128

Бренд: PANCONTROL Страницы: 157

Бренд: Omega Страницы: 16

Бренд: A&D Страницы: 10

Бренд: ICP DAS USA Страницы: 4

Бренд: G4M Страницы: 52

83620B 8360 Series

Бренд: Agilent Technologies Страницы: 2

Бренд: E+E Elektronik Страницы: 48

Бренд: Velleman Страницы: 18

SensoControl ServiceJunior

Бренд: Parker Страницы: 18

Xtrinsic MMA8491Q

Бренд: Freescale Semiconductor Страницы: 4

Бренд: Swema Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды