GEA Futuro Скачать руководство пользователя страница 64

Страница: 64 / 108

Installation

Installation of the evacuation line

2007-9015-001
03-2014

64 / 108

Space the anodes along the evacuation line as shown.

Anodes

Activation of the sacrificial anode

Attention!

Discard any plastic film that may have been wrapped around the
anode cardboard tube for handling. Do not remove the plastic caps
from the cardboard tube.

The dry conductive powder in the cardboard tube must be saturated with water
before burying the sacrificial anode.

● Using a knife, make a cut in the plastic cap and fill the tube with water.

● The cardboard will disintegrate within months and the natural moisture of the

soil will keep the conductive powder humidified through the years.

Legend:

Anode copper wire AWG #12/7

Cut in plastic cap

High purity magnesium bar*

Plastic cap

Conductive powder

Insulated welded connection

Galvanized steel sheet

Cardboard tube

* This bar will disintegrate slowly over several years.

Содержание Futuro













































































































Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды

GEA Futuro, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды