GEA Futuro Скачать руководство пользователя страница 72

Страница: 72 / 108

Initial Commissioning

Checks before initial commissioning

2007-9015-001
03-2014

72 / 108

6.3

Checks before initial commissioning

The owner should ensure that:

● Each point of the warranty registration form have been met.

● Oil in the hydraulic power unit tank is at proper level.

● 2 ball valves under hydraulic power unit have been opened.

● 2” [5cm] of biodegradable oil is poured above the piston. Refer to section on

Lubricant specifications.

● All personnel who perform work on or with the product must carefully read,

understand and act in accordance with the instructions.

● All stationary components are securely anchored to the floor.

● All grease zerks have been lubricated.

● All guards and covers are in place.

● All installation materials and debris are cleaned up and removed from the

equipment.

● Check the product for visible damage; immediately remove any faults that

are found (note personnel qualification required) or send to the specialist
dealer - the product may only be used if it is perfect condition.

Hydraulic power unit

● Ensure the oil reservoir of the

hydraulic power unit is 2/3 full. Refer
to section on Lubricant
specifications.

Oil sight

gauge

● Ensure 2 ball valves have been opened as shown below.

Содержание Futuro













































































































Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды

GEA Futuro, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды