GEA D-tec D Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 106

background image

11

Alarms

11.1

Malfunctions and remedies

Notice

Warning of damage to property/loss of product

Ignoring malfunctions may cause considerable damage to property and loss
of product. The safe operation of the valve in the event of a malfunction can
no longer be taken for granted and in the worst case can result in a loss of
sterility in the process.
► Make sure that malfunctions are quickly identified and promptly fixed.

In the event of malfunctions immediately deactivate the valve and secure it
against inadvertent reactivation. Malfunctions may only be remedied by qualified
staff, who must observe the safety precautions.

Malfunction

Cause

Remedy

Valve does not work

Fault in the controller

Check the system
configuration

No compressed air or
compressed air too low

Check compressed air supply
and check air hoses for free
passage and air tightness

Fault in the electrical system

Check actuation / external
controller and routing of
electrical lines

Solenoid valve defective

Replace the solenoid valve

Valve does not close

Dirt/foreign material between
valve seat and valve disk

Clean valve housing and valve
seat

Valve closes too slowly

O-rings in actuator and control
top are dry (friction losses)

Grease O-rings

Leak at the valve seat.

The valve seat seal is
defective.
Product deposits on the valve
seat.

Replace the valve seat seal.
Check the housing.

Fault in the leakage housing or
the leakage display

Stem diaphragm defective

Disassemble valve and change
both stem diaphragms.

The TEFASEP gold valve seat
seal is not tight after
commissioning or
maintenance.

The valve seat seal is not
properly installed or has been
damaged during assembly or
disassembly.
In case of a new seal: Do not
perform any valve switching
during/directly after CIP or SIP
cleaning.

Perform valve switching
during/directly after CIP or SIP
cleaning.

Leakage in the side valve

Faulty stem seal

Replace stem seal

Alarms

Malfunctions and remedies

430BAL013307EN_8

82

04.08.2022

«
...
80
81
82
83
84
...
»

Содержание D-tec D











































































































Отзывы:

Нет отзывов

Похожие инструкции для D-tec D

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Vacon Страницы: 64

Бренд: CAME Страницы: 32

Бренд: BADODOSECURITY Страницы: 8

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды