GE NX-4V2 Скачать руководство пользователя страница 6

Страница: 6 / 48

NX-4V2 Control

V. TERMINAL

DESCRIPTIONS

TERMINAL

DESCRIPTION

House Telephone Ring (Grey).

Telephone Ring (Red).

Telephone Tip (Green).

House Telephone Tip (Brown).

AC input. Connect to a 16.5V 40 or 50 VA Class ll U.L. approved transformer.

EARTH

Earth Ground. Connect to a cold water pipe or a 6 to 10 foot driven rod.

AUX1

Connect negative lead of low current device [relay, LED (install 1K

Ω

resistor in series with LED), etc.].

Connect positive lead of device to COM. Current is limited to 250mA when output is negative, and 250

when output is positive.

SIREN

If used as a siren output (default), the speaker rating should be 15 watt at 8 or 16 ohm, or 30/40 watt at 4, 8,
or 16 ohms. If voltage output is selected in location 37, this output becomes voltage output, 12VDC, 1 Amp
maximum load.

NOTE:

A 3.3K

Ω

resistor may be required across the bell terminals when a 12 VDC

siren is used. If no resistor is used, you may experience voltage leakage into the siren, which will
cause these devices to output a small signal.

COM

Connect negative wire of powered devices such as motion detectors and smoke detectors.

SMOKE+

Smoke detector power 12VDC, 1.5 amps maximum (For those jurisdictions which allow the Priority zone to
be used with smoke detectors.)

AUX2

Connect negative lead of low current device [relay, LED (install 1K

Ω

resistor in series with LED), etc.].

Connect positive lead of device to COM. Current is limited to 250mA when output is negative, and 250

when output is positive.

DATA

Connect to the data terminal on the keypads and the expanders. Maximum number of devices: 8 k 1
other device. See

Maximum Wire Run

chart below.

COM

Connect to the Common terminal on the keypads and the expanders.

POS

Connect to the POS terminal on the keypads and the expanders. Individually, this terminal is limited to 1
Amp.

ZONE 4

Connect to one side of zone 4 loop. Connect the other side to com terminal. Open or short causes alarm.

COM

Common (-) terminal for zones 3 & 4. (See the wiring diagram for examples.)

ZONE 3

Connect to one side of zone 3 loop. Connect the other side to COM terminal. Open or short causes alarm.

ZONES 1- 2

Connect as described for zones 3 & 4

NETWORX KEYPAD MAXIMUM WIRE RUN

(Note:

These numbers are for one keypad at the end of the wire. When connecting more than one keypad to the end of the wire, a

higher gauge wire will be required.)

WHEN CONNECTED TO NX-4V2

WHEN CONNECTED TO NX320-E

Length in feet

Wire Gauge

250 24

500 20

1000 18

1500 16

2500 14

WWW.DIYALARMFORUM.COM

Содержание NX-4V2

















































Результаты поиска

Содержание NX-4V2

Отзывы:

GE NX-4V2, Установка и запуск, Страница: 6 / 48

Результаты поиска

Содержание NX-4V2

Отзывы: