manualshive.com logo in svg

GE NX-4V2, Установка и запуск, Страница: 19 / 48

Поделиться
Скачать
GE NX-4V2 Скачать руководство пользователя страница 19

 

NX-4V2 Control 

 

19 

L 

40 SYSTEM 

TIMERS 

14........... numerical 

Location 40 contains the duration of various system timing functions.  Example: If you desire the duration of the Dynamic Battery Test 
to be 30 minutes, you should program [3]-[0]-[

r

] in segment 1 of this location.  The [3]-[0] is the number of minutes, and the [

r

] stores 

the data and moves to the next segment of this location. 
 

NOTES FOR UL INSTALLATIONS 

The "Listen-In" feature cannot be enabled for UL Listed systems. 
The "Dynamic Battery Test" feature cannot exceed four (4) hours. 
The dial delay shall be set to -0-.  Must be disabled by zone type in Loc 110-169. 
The combined Dial Delay and Entry Delay (loc 24) must not exceed 1 minute for SIA CP-01 requirements. 

 

Segment 1 

-  

Dynamic Battery Test duration in minutes 0-255 minutes ..................................... (0 = no test) 

Segment 2

  - 

AC Fail report delay in minutes 0-255 minutes. .................................................... (0 = no delay) 

Segment 3

 - 

Power Up Delay in seconds 0-60 seconds ........................................................... (0 = no power up delay) 

Segment 4

 -  

Siren Time in minutes 1-254 minutes. 

Segment 5

 -  

Telephone Line Cut delay in seconds 0-255 seconds........................................... (0 = no TLM) 

Segment 6

 -  

Cross Zone time in minutes 0-255 ........................................................................ (0 = no cross zoning)  

Segment 7

 -  

Chime time in 50 mS (1/20th second) increments from 0-12 seconds .................. (0 = follows zone 255 latched) 

Segment 8

 - 

Dial delay in seconds 15-255 seconds.................................................................. (0 = no abort delay) 

Segment 9

 - 

Fire Alarm Verification time in seconds 120-255 seconds..................................... (0 = no fire alarm verification) 

 

NOTE:  The fire alarm verification feature is not approved for residential use in California 

Segment 10 -

 

Listen-In time in seconds 0-255 ............................................................................ (0 = no Listen-In time) 

Segment 11 - 

Zone Activity Monitor feature timed in days 0 – 255 ............................................. (0 = disabled)

 

Segments 12-14

  Reserved. 

 
 

 41  SPECIAL 

FEATURES 

1............. feature select 

Segment 1: 

1 =   On enables the 6-digit code option.  If 6-digit option is enabled, all arm/disarm codes and the "Go To Program Code" are 6 

digits.  If this option is enabled, the default user 1 code is [

1

]-[

2

]-[

3

]-[

4

]-[

5

]-[

6

]. 

 

 

NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE "GO TO PROGRAM CODE" IS A SIX-DIGIT CODE 
BEFORE EXITING PROGRAMMING.

 

2 =   On requires code entry for [

r

]-[

9

]-[

8

] (perform call back download) and [

r

]-[

9

]-[

9

] (answer incoming call for download) 

functions. 

3 =   Enable Auto Cancel / Abort (Refer to Glossary beginning on page 35) 
4 =   Enable Walk-Test Mode (Refer to Glossary beginning on page 35) 
5 =   On enables Auto Force-Arming with keyfob or keyswitch. 

 

L

  

42 

GO TO PROGRAM CODE 

6............. numerical 

Location 42 contains the "Go To Program Code".  This location contains either a 4 or 6-digit code. If the 6-digit code option is enabled 
in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS.  If this option is not enabled in location 41, the last 2 segments (digits) 
will be ignored.  With the NX-4V2 disarmed, the "Go To Program Code" can be used to enter the Program Mode. 
 

 

 

43 

GO TO PROGRAM CODE & AUTHORIZATION 

2............. feature select 

The "Go To Program Code" can be used as a standard arm/disarm code.  When using the code to arm or disarm, the user ID is 255. 
(This code may not be changed in the Run Mode.) 
 

Segment 1:

 

 

1 =  Reserved. 
2 =  On enables "Go To Program Code" as an arm only code. 
3 =  On enables "Go To Program Code" as an arm only after closing. 
4 =  On enables "Go To Program Code" as a master arm/disarm code (can change user codes) 
5 =  On enables "Go To Program Code" as an arm/disarm code.  
6 =  On enables "Go To Program Code" to bypass zones. 
7 =  On enables "Go To Program Code" opening and closing reports. 
8 =  Reserved. 

 

Segment 2:  

Reserved

 

 

L

  

44 

DURESS CODE 6............. numerical 

Location 44 contains the "Duress" code.  This Location contains either 4 or 6 digits. If the 6-digit code option is enabled in Location 41, 
THIS CODE MUST CONTAIN SIX (6) DIGITS.  If the 6-digit option is not enabled in location 41, the last 2 digits will be ignored.   
 

 45  RESERVED 

 

WWW.DIYALARMFORUM.COM

Содержание NX-4V2

















































Отзывы:

Нет отзывов