GE NX-4V2 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 48

GE NX-4V2 Скачать руководство пользователя страница 41

NX-4V2 Control

41

XVIII. APPENDIX

3

EXPANDER NUMBERS FOR REPORTING EXPANDER TROUBLE

The tables below list the device numbers that will be reported for trouble conditions.

Device

Device # reported

NX-4V2 Control Panel

0

See page 39 for possible report codes.

NX-534E Two Way Listen-In

64

NX-540E “Operator”

40

NX-591E Cellemetry Interface

76

KEYPADS

REMOTE POWER SUPPLY (NX-320E)

KEYPAD

DEVICE #

Switch Setting

Address

1

192

All switches off

84

2

200

Switch 1 on

85

3

208

Switch 2 on

86

4

216

Switch 1 & 2 on

87

5

224

Switch 3 on

88

6

232

Switch 1 & 3 on

89

7

240

Switch 2 & 3 on

90

8

248

Switches 1, 2, & 3 on

91

WIRELESS RECEIVER (NX-448E)

OUTPUT MODULE (NX-508E)

Switch Setting

Expander # reported

Switch Setting

Address

All switches off

35

Switch 1 & 2 on

24

Switch 1 on

36

Switch 3 on

25

Switch 2 on

37

Switch 1 & 3 on

26

Switches 1 & 2 on

38

Switch 2 & 3 on

27

Switch 3 on

39

Switch 1,2,&3 on

28

Switches 1 & 3 on

32

All switches off

29

Switches 2 & 3 on

33

Switch 1 on

30

Switch 1, 2 & 3 on

34

Switch 2 on

31

XIX. APPENDIX

4

USER ID OR ZONE ID HEX DIGIT FOR 4+2 FORMATS

The following appendix applies only to slow formats (locations 56- 83 lower digit).

The digit programmed in the locations will be

sent as the upper HEX digit in place of the alarm event code. The zone ID or user ID will always be reported as the lower HEX digit (1-
F) as shown in the chart below. For example, if the zone ID or user ID is 6, the 4+2 lower digit will be “6”. Use the chart shown below
for convenience.

If Segments 2-8 are left as “0” (unprogrammed), they will follow the Segment 1 selection. If Segment 1 is left as “0” and the

feature is enabled in Location 23, the NX-4V2 will report “A”.

ZONE
USER

HEX

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

WWW.DIYALARMFORUM.COM

«
...
39
40
41
42
43
...
»

Содержание NX-4V2

















































Отзывы:

Нет отзывов