GE Mini COM Express 10 Скачать руководство пользователя страница 20

Страница: 20 / 82

3.2

General Installation Guidelines

Adhere to the following guidelines during installation:

•

Observe all safety procedures to avoid damaging the system and protect operators
and users.

•

Before installing or removing any board, verify that the system power and external
supplies have been turned off.

•

Verify that the jumpers on the carrier board are correctly configured for your
application.

•

Mount the board on the carrier board very carefully. Refer to the procedure,

To install

the mCOM10-L1500 onto the carrier board

•

Do not restore power until all modules are fitted correctly and all connections have
been made properly.

GFK-2896

Mini COM Express Type 10 Module mCOM10-L1500

For public disclosure

Содержание Mini COM Express 10



















































































Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды

GE Mini COM Express 10, Справочник по аппаратуре

Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды