GE Mini COM Express 10 Скачать руководство пользователя страница 22

Страница: 22 / 82

3.3.2

Install the Combined Unit

�

To install the mCOM10-L1500 plus carrier board into a system

Before installing or removing any board, verify that the system power and external
supplies have been turned off.

Verify that the jumpers, if any, are correctly configured for your application.

Mount the unit very carefully.

Connect all I/O cables.

When all units are correctly fitted into the system and all connections have been
made properly, restore power.

3.4

Initial Startup

A few seconds after powerup, the mCOM10-L1500 system UEFI Firmware banner
displays on the screen. If you do not see any error messages up to this point, the board is
running properly and ready to be installed and configured for your application.

3.4.1

UEFI Firmware Setup

Contact GE Intelligent
Platforms for technical
support. Refer to the section,

Support, Service, and
Warranty

�

To enter setup during the initial startup sequence:

press the

Delete

during the boot up sequence. Adhere to the applicable on-screen messages when
prompted.

GFK-2896

Mini COM Express Type 10 Module mCOM10-L1500

For public disclosure

Содержание Mini COM Express 10



















































































Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды

GE Mini COM Express 10, Справочник по аппаратуре

Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды