GE Mini COM Express 10 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 82

background image

5.1.1.2

Carrier Board Termination

The following signals require carrier board termination for proper operation. If the signals
and features are not used, no carrier board termination is required and the pins may be left
open.

Ethernet

External Ethernet magnetics are implemented on the carrier board.

LVDS

The LVDS flat panel differential pairs (LVDS_A/B[0:3] ±, LVDS_A/B_CK ±)

should have 100 [ termination across the pairs at the destination. This may be on the
carrier board if the carrier board implements an LVDS de-serializer on-board.

USB_0_1_OC#, USB_2_3_
OC#, USB_4_5_OC#, and
USB_6_7_OC# signals are
used to flag a USB
over-current situation.

USB

No termination is required on USB pairs. A common mode choke and ESD

protection is advisable if USB pairs on the carrier board are routed to a connector for use
with an external cable. Carrier board USB overcurrent monitors may pull the

USB_

[0,2,4,6]_[1,3,5,7]_OC#

l lines to GND with open drain drivers to indicate that the

monitorʹs current limit has been exceeded. Do not pull up these lines to 3.3 V on the
carrier board; this is done on the module.

PCI Express

At the module, the PCI Express transmit signals have ac coupling

capacitors. For the carrier PCIe transmit lines (receive at the module), ac coupling must
be located at the carrier.

DDI Ports

Carrier-based terminations are dependent on the video interface supported

by the module, as follows:

•

DDI0 is an interface for Display Port or TMDS (DVI/HDMI)

•

DC blocking capacitors are placed on the carrier for the

DDI0_PAIR[0:3]

signals.

•

The carrier includes a blocking Field Effect Transistor (FET) on

DDI[n]_HPD

to

prevent back-drive current from damaging the module.

Configuration

GFK-2896 Hardware Reference Manual 39

For public disclosure

«
...
37
38
39
40
41
...
»

Содержание Mini COM Express 10



















































































Отзывы:

Нет отзывов

Похожие инструкции для Mini COM Express 10

Бренд: DAV TECH Страницы: 10

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Kärcher Страницы: 4

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: K&K Страницы: 6

Бренд: Hach Страницы: 504

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды