GE Mini COM Express 10 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 82

background image

2.2

Package Contents

Verify that the delivered package contains one mCOM10-L1500 module.

2.3

Unpacking and Inspecting

Warning

Before installing or removing any board, ensure that
the system power and external supplies have been
turned off.

Warning

After unpacking the module, inspect it for visible
damage that could have occurred during shipping or
unpacking. If damage is observed (usually in the form
of bent component leads or loose socketed components),
contact GE Intelligent Platforms for additional
instructions. Depending on the severity of the damage,
it may be necessary to return the product to the factory
for repair.

DO NOT apply power to the board if it has visible
damage. Doing so may cause further, possibly
irreparable damage, as well as introduce a fire or shock
hazard.

Attention

Retain all packing material in case of future need.

Before unpacking the board or module, or fitting the device into your system, read the
manual carefully. Also adhere to the following guidelines:

•

Observe all precautions for electrostatic sensitive modules

•

If the product contains batteries, do not place the board on conductive surfaces,
anti-static plastic, or sponge, which can cause shocks and lead to battery or board
trace damage. Do not exceed the

operational temperatures. Batteries and

storage devices might also have temperature restrictions.

•

Keep all original packaging material for future storage or warranty shipments of the
board.

Although the module is carefully packaged to protect it against the rigors of shipping, it is
still possible that shipping damages may occur. Careful inspection of the shipping carton
should reveal some information about how the package was handled by the shipping
service. If evidence of damage or rough handling is found, notify the shipping service and
GE Intelligent Platforms as soon as possible.

16

GFK-2896

Mini COM Express Type 10 Module mCOM10-L1500

For public disclosure

«
...
14
15
16
17
18
...
»

Содержание Mini COM Express 10



















































































Отзывы:

Нет отзывов

Похожие инструкции для Mini COM Express 10

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Vacon Страницы: 64

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды