GE iBox Скачать руководство пользователя

Страница: 164 / 172

iBox/iBox Kit

Installation and Maintenance Guide

GE Grid Solutions

164

994-0047-5.10-4

GE Information

Installing DNP3 I/O Modules in a Rack

Rack Spacing

When mounting multiple DNP3 I/O modules in a rack, or when mounting DNP3 I/O modules in a rack

with other equipment , verify that there is at least one rack unit (RU) of space above and below the

DNP03 I/O module to allow for cooling air flow and cable routing (1 RU = 1.75 inches or 44.5 mm).

Required Clearances

The exterior dimensions of the DNP3 I/O module are:

Dimension

Measurement

Width

19 inches (483 mm)

Height

5.25 inches (133.4 mm)

Depth

2.5 inches (63.5 mm)

Allow about 14 inches (356 mm) of total cabinet depth, to provide clearance for cables and maintenance

access.

Rack Mounting Procedure

To mount the DNP3 I/O module in a rack:
1. Determine the location of the DNP3 I/O module in a 19-inch mounting rack.
2. Install, but do not tighten the top two mounting screws.

Note

Install the DNP3 I/O module with the LEDs visible from the front of the rack.

3. Slide the DNP3 I/O module over the top mounting screws and drop down into position.
4. Insert the bottom mounting screws.
5.

Tighten all four mounting screws.

You are now ready to connect ground to the DNP I/O module. See “Connecting to protective ground” on

page

165

Содержание iBox













































































































































































Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды

GE iBox, Руководство по установке и обслуживанию

Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды