GE iBox Скачать руководство пользователя

Страница: 140 / 172

iBox/iBox Kit

Installation and Maintenance Guide

GE Grid Solutions

140

994-0047-5.10-4

GE Information

Section 4:

Removing Configuration Data and

Sensitive Information

Overview

In the event that it is necessary to remove the configuration data and sensitive information

from the iBox (for example, the iBox is being disposed of or being returned for

maintenance [i.e., RMA]), this section provides the data removal procedure.
It may also be necessary to remove data from a PC that has run SGConfig for the purpose

of configuring a iBox. Again, this section provides the data removal procedure.

4.1. From the iBox Device

Method

The configuration data can be removed from these devices by either:

•

Removing the battery from the device for at least 5 minutes.

Result: The configuration data which was backed up in NVRAM is removed, since

the NVRAM is powered by a battery.
Note: This does not remove the firmware running in the flash memory.

•

Restarting the device:
1.

Restart the device by either:

•

Turning the power off and on, or

•

Typing the

boot

command at the 68K monitor prompt.

When messages appear on the 68k monitor prompt, press the

Esc

key a few

times within 5 seconds.
Result: The message: “Are you sure you wish to generate a default

configuration? (y/n)” appears.

3. Type

(or

Result: The current configuration file is overwritten with the default

configuration. The 68k monitor is initiated. The configuration has been defaulted

to a factory-based configuration and the user’s configuration has been deleted.

4. Remove the firmware from the flash memory:

a. Login to the device through the 68K monitor (if not already logged in).
b. Type

to suspend all processes running on the device.

c. Type

erase

to clear the flash.

Result: This takes several seconds to complete.
Result: The Flash Erased message appears when the erase operation is

completed.

5. Confirm the flash has been erased by typing img at the prompt to view the image

file.
Result: No firmware information should appear.

Содержание iBox













































































































































































Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды

GE iBox, Руководство по установке и обслуживанию

Результаты поиска

Содержание iBox

Отзывы:

Похожие инструкции для iBox

Бренды по названию

Популярные бренды