GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя | Manualshive

Страница: 58 / 74

background image

– 58 –

Control Diagnostics Using the Temperature Display On Non-Dispenser Models

The temperature display has a self-diagnosis mode that can be accessed and will help the technician to test
certain functions of the temperature display, defrost heater, damper, and interior fan. This mode can aid the
service technician in quickly identifying failed or improper operation of certain components and systems.

Control diagnostics using the display does not use error codes to identify problems. Instead, the temperature
display allows access to components or systems to be checked if a problem is detected.

The temperature display must be in an active mode before entering the self-diagnosis test. If the display is
blank, press any temperature button once, then release it. The display will show actual temperatures.
Enter the diagnostic mode by pressing both the freezer temperature (COLDER and WARMER) pads and
the refrigerator temperature (COLDER and WARMER) pads simultaneously. All four pads must be held for
approximately 3 seconds. Blinking "0"s in both the freezer and refrigerator sections of the display indicate
the refrigerator has entered the test mode. Remove

fi

ngers within 5 seconds and press any pad to lock-in

the test mode. The blinking "0"s will change over to solid (non-blinking) "0"s when the test mode is locked-
in. Failure to lock-in the test mode within 30 seconds will time out the test and return the refrigerator to the
normal cooling mode.

FZ

Display

FF

Display

Mode

Comments

0

1

Showroom Mode

When activated, a tone will sound brie

fl

y and the display

will

fl

ash 1 time. The cooling system stops operation. All

HMI functions will operate normally.

0

2

Display Combined HMI
Software Version

Temperature to main controls communications test. A

coded software version is displayed. Dispenser model
will show two numbers.

See Note 1

. Internal display

model will test for Pass/Fail. Should show "P". If the
format is violated, the display will read "99".

0

3

Display Main Control
Software Version

Temperature to dispenser communications test. A coded

software version is displayed. Dispenser model will show
two numbers.

See Note 1

. Internal display model will

show "F" (no dispenser board). If the format is violated,
the display will read "99".

0

4

Combined HMI to Main
communications

Dispenser to main controls communications test.
Dispenser model will test for Pass/Fail. Should show "P".
Internal display will show "F" (no dispenser board).

(

Continued next page

)

Temperature Display On Non-Dispenser Models

«
...
56
57
58
59
60
...
»

Содержание PGCS1NFXSS











































































Отзывы:

Нет отзывов

Похожие инструкции для PGCS1NFXSS

Бренд: DAEWOO ELECTRONICS Страницы: 15

Бренд: GE Страницы: 52

CoolScapes GB Series

Бренд: Delfield Страницы: 28

Бренд: Goddess Страницы: 76

Бренд: U-Line Страницы: 57

Бренд: Randell Страницы: 4

Бренд: Adler Europe Страницы: 72

Бренд: Arctica Страницы: 9

Бренд: U-Line Страницы: 50

Бренд: Hisense Страницы: 14

Бренд: Summit Страницы: 12

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 12

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 17

Бренд: Zanussi Страницы: 10

Бренд: Zanussi Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды