GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя | Manualshive

Страница: 32 / 74

background image

– 32 –

Evaporator

Cold Air
Mixed Air
Air Return To
Evaporator

Fresh Food

Freezer

Airfl ow

The evaporator fan forces air through the evaporator into the freezer compartment.

Air from the evaporator can also pass through the electronic damper to the air tunnel outlet, through the
fresh food compartment, and return to the evaporator.

The damper is controlled by the main control board. When open, the damper allows the chilled air from the
freezer to move into the fresh food compartment.

Air returns from the fresh food compartment to the freezer compartment via two vents located to the left
and right of the electronic damper.

*Return Duct (1 of 2)

* Return air ducts are located in the
freezer liner behind the evaporator and
are not replaceable.

«
...
30
31
32
33
34
...
»

Содержание PGCS1NFXSS











































































Отзывы:

Нет отзывов

Похожие инструкции для PGCS1NFXSS

Бренд: Haier Страницы: 14

Бренд: RAPA Страницы: 20

Бренд: Zanussi Страницы: 20

Бренд: Amica Страницы: 100

Бренд: Heinner Страницы: 60

Бренд: JUNO Страницы: 9

Бренд: Hallman Страницы: 92

Бренд: Monogram Страницы: 16

Бренд: BOMANN Страницы: 36

Бренд: V-ZUG Страницы: 36

TT TU 133 F S180C

Бренд: VALBERG Страницы: 26

Бренд: Ravanson Страницы: 87

Бренд: U-Line Страницы: 47

Бренд: VALPRO Страницы: 31

Бренд: Dometic Страницы: 124

Бренд: Lec Страницы: 20

Бренд: Gaggenau Страницы: 23

Бренд: Logik Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды