background image

– 2 –

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by
individuals possessing adequate backgrounds of electrical,
electronic, and mechanical experience. Any attempt to repair a
major ap pli ance may result in personal injury and property 
damage. The man u fac tur er or seller cannot be responsible for the 
in ter pre ta tion of this in for ma tion, nor can it assume any liability in 
connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing 
this prod uct. If electrical power is required for diagnosis or test 
purposes, disconnect the power immediately after performing the 
necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to 
complete a path to ground are removed for service, they must be 
returned to their original position and properly fastened.

GE Consumer & Industrial

Technical Service Guide

Copyright © 2008

All rights reserved. This service guide may not be reproduced in whole or in part
in any form without written permission from the General Electric Company.

Содержание PGCS1NFXSS











































































Отзывы: