GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя | Manualshive

Страница: 17 / 74

background image

– 17 –

4. After replacing light bulb with an appliance bulb

of the same or lower wattage, replace the shield.

5. Plug the refrigerator back in.

Refrigerator LED Lights

Note:

Setting the controls to

OFF

does not remove

power to the LED light circuit.

The refrigerator utilizes 12 LED lights that are
permanently contained in a

fi

xture and cannot be

replaced separately. The

fi

xture is attached to the

ceiling of the fresh food section with 3 Phillips-head
screws.

The

fi

xture is connected to the refrigerator with a

wire harness. After removing the screws, the wire
harness can be disconnected.

Disconnect

(

Continued next page

)

The LED light

fi

xture is powered by a transformer

assembly that is located behind the water valve
in the machine compartment. The assembly
consists of a bracket, transformer, circuit board, and
replaceable fuse.

Note

Determine and correct the cause of fuse

•

failure when replacing the 3-amp fuse (part #
WR55X10766).

The replacement transformer assembly is

•

supplied as a complete unit. The bracket,
transformer, and circuit board cannot be
ordered separately.

On later production models, the fuse is

•

eliminated in the LED transformer assembly.

Fuse

Transformer Assembly Removed

Bracket

Refrigerator Lights

Incandescent Lights

CAUTION:

Light bulbs may be hot.

Note:

Setting the controls to

OFF

does not remove

power to the light circuit. Reveal

®

appliance bulbs

are used on some models. They can be identi

fi

ed by

their blue color when they are not illuminated.

The 2 refrigerator bulbs and the single freezer bulb
are located inside light shields. Each light shield
is located at the top of the freezer or refrigerator
compartment.

To remove the bulb:

Unplug the refrigerator.

1.

Grasp the shield at the back and pull out to

2.

release the tabs at the back.

Rotate the shield down and then forward to

3.

release the tabs at the front of the shield.

«
...
15
16
17
18
19
...
»

Содержание PGCS1NFXSS











































































Отзывы:

Нет отзывов

Похожие инструкции для PGCS1NFXSS

Profile PSB42YGXSV

Бренд: GE Страницы: 5

Бренд: Gaggenau Страницы: 81

RC472700 - annexe 2

Бренд: Gaggenau Страницы: 60

Бренд: Gaggenau Страницы: 77

Бренд: Gaggenau Страницы: 33

Бренд: Gaggenau Страницы: 82

Бренд: Gaggenau Страницы: 36

Бренд: Gaggenau Страницы: 87

Бренд: Gaggenau Страницы: 53

Бренд: V-ZUG Страницы: 24

Бренд: Samsung Страницы: 260

CombiCooler V4000 178KNI

Бренд: V-ZUG Страницы: 40

Бренд: U-Line Страницы: 44

Бренд: Gram Страницы: 48

599 Premium Wine Cellar Series

Бренд: AGA Страницы: 16

Бренд: Jenn-Air Страницы: 28

Бренд: Smeg Страницы: 13

Бренд: Vinotemp Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды