GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя

Страница: 52 / 74

– 52 –

Note:

The dispenser trim is held to the dispenser

recess by 5 retaining tabs along each side and 2 at
the top.

Using your hands or a plastic putty knife,

carefully lift or pry the dispenser trim away from
the dispenser recess.

Dispenser Switch (rear view)

Switch

EMI Filter

The EMI Filter is accessed from the back of the

refrigerator and is located on the left side of the
compressor.

To remove the EMI fi lter:

Remove the 5/16-in. hex-head screw that

attaches the bracket to the cabinet.

Pull the bracket out and remove the 1/2-in. nut.

Cut the 2 plastic wire ties that hold the EMI

lter

to the bracket.

Mark and disconnect the wires from the EMI

lter.

5/16-in.Screw

1/2-in. Nut

Wire Tie

Содержание PGCS1NFXSS











































































Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды

GE Consumer & Industrial PGCS1NFXSS, Техническое обслуживание руководство

Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды