GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя | Manualshive

Страница: 25 / 74

background image

– 25 –

Freezer Drawers

Freezer Drawer Handle Removal

Note:

Each freezer drawer handle is held in place

by a left and a right fastener, and locked in position
by 2 recessed 1/8-in. Allen screws. Each fastener
is located behind the handle and attached to the
drawer panel.

Using a 1/8-in. Allen wrench, loosen the 2 recessed
screws, then pull the handle straight out from the
door.

Note:

If the handle mounting fasteners need to be

tightened or removed, use a 3/16-in. Allen wrench.

1/8-in. Allen Wrench

3/16-in. Allen Wrench

Fastener

Upper Drawer Front Vertical Adjustment

Note:

This following instruction is for adjusting the

upper drawer front vertically to meet appearance
needs of the customer. Both the right and left side of
the drawer front can be adjusted independently.

To adjust the upper drawer front vertically:

Remove the full-width basket. (See

1.

Freezer

Basket Removal

.)

Remove the pilot screw on the side of the

2.

drawer front that needs to be adjusted. Do one
side at a time if both need adjustment.

3. Loosen the remaining three 10-mm hex-head

screws, on the side that needs to be adjusted, 3
full turns.

4. Raise or lower the side of the drawer front,

requiring adjustment to the desired position.
Once positioned, tighten the 3 screws.

Note:

Do not replace the pilot screw once the

drawer front is adjusted. It is no longer needed.

Left Side Bracket Shown

Loosen

Loosen

Loosen

Pilot Screw

Remove

Do Not

Remove

Upper Drawer Front Removal

To remove the upper drawer front:

Remove the full-width basket. (See

1.

Freezer

Basket Removal

.)

(

Continued next page

)

«
...
23
24
25
26
27
...
»

Содержание PGCS1NFXSS











































































Отзывы:

Нет отзывов

Похожие инструкции для PGCS1NFXSS

Бренд: Danby Страницы: 4

Бренд: Gaggenau Страницы: 81

RC472700 - annexe 2

Бренд: Gaggenau Страницы: 60

Бренд: Gaggenau Страницы: 77

Бренд: Gaggenau Страницы: 33

Бренд: Gaggenau Страницы: 82

Бренд: Gaggenau Страницы: 36

Бренд: Gaggenau Страницы: 87

Бренд: Gaggenau Страницы: 53

Бренд: Igloo Страницы: 7

Бренд: Igloo Страницы: 10

Бренд: Igloo Страницы: 1

Бренд: Igloo Страницы: 1

Бренд: Häfele Страницы: 53

Бренд: U-Line Страницы: 15

Бренд: Zanussi Electrolux Страницы: 14

Бренд: Daewoo Страницы: 39

Бренд: DAEWOO ELECTRONICS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды