GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя | Manualshive

Страница: 22 / 74

background image

– 22 –

Refrigerator Door Removal

Tape the doors shut with masking tape.

1.

Note:

The following procedure applies to removing

the right-side door with dispenser. On non-dispenser
models, follow this same procedure for removing
the right-or left-side doors. There are no wires,
water lines, or center hinge covers on non-dispenser
doors.

2. Remove the screw securing the center hinge

cover.

3. Pull the left side of the hinge cover out and

remove the cover from the hinge.

4. Using

a

fl

at blade screwdriver, push down and

remove the metallic water line support.

5. Using

a

fl

at blade screwdriver, push the red

plastic locking clip down and off.

6. Carefully push the red collar in while pulling the

water line out from the coupling.

*Collar

Water Line

*Replacement collar unavailable

Refrigerator Doors

Refrigerator Door Handle Removal

Note:

Each refrigerator door handle is held in place

by an upper and lower fastener and locked in
position by 2 recessed 3/32-in. Allen screws. Each
fastener is located behind the handle and attached
to the door panel.

Using a 3/32-in. Allen wrench, the 2 recessed screws
can be loosened, then the handle can be pulled
straight out from the door.

Note:

If the handle mounting fasteners need to be

tightened or removed, use a 3/16-in. Allen wrench.

Cover

Clip

Fastener

3/32-in.

Allen

Wrench

3/16-in.

Allen

Wrench

Fastener

Support

(

Continued next page

)

(Appearance may vary)

«
...
20
21
22
23
24
...
»

Содержание PGCS1NFXSS











































































Отзывы:

Нет отзывов

Похожие инструкции для PGCS1NFXSS

Бренд: Zanotti Страницы: 86

Бренд: Waeco Страницы: 344

SIDE-BY-SIDE REFRIRATOR 22

Бренд: GE Страницы: 112

SIDE-BY-SIDE REFRIRATOR 22

Бренд: GE Страницы: 132

SIDE-BY-SIDE REFRIRATOR 22

Бренд: GE Страницы: 88

Profile PSB42YGXSV

Бренд: GE Страницы: 100

SIDE-BY-SIDE REFRIRATOR 22

Бренд: GE Страницы: 64

Бренд: GE Страницы: 2

ENERGY STAR GTH18GBDBB

Бренд: GE Страницы: 2

ENERGY STAR GSS23QSTSS

Бренд: GE Страницы: 2

Бренд: GE Страницы: 108

Бренд: GE Страницы: 120

Бренд: GE Страницы: 2

Бренд: U-Line Страницы: 2

Visair IN-VA10-A004

Бренд: FPG Страницы: 40

Бренд: Saivod Страницы: 64

Бренд: Cylinda Страницы: 152

Бренд: Tesla Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды