GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя

Страница: 57 / 74

– 57 –

Note 1:

Display order is #1 = Fresh Food Thermistor, #2 = Ambient Thermistor, #3 = Freezer Thermistor, #4 =

Freezer Evaporator Thermistor, #5 = Invalid (not used).

Thermistor test results are: P = Pass, 0 = Fail, S = Short to 5 VDC, B = Defective board (replace main control).

Note 2:

You

must

enter the defrost test again to toggle the defrost heater off at the end of the test. The

heater will not come on if the evaporator thermistor is above 50°F (21°C).

Freezer

Display

Fresh

Food

Display

Diagnostics

Results

Comments

Control and Sensor System Test

Checks each
thermistor in order.

See Note 1

Damper Test

Damper will open for
10 seconds.

Test will not start for
approximately 10
seconds after pad is
pressed.

Fan Test

Cycles through each
fan for 5 seconds.

100% Run Time

Sealed system on
100% of the time.
Times out after 1
hour.

Prechill Test

Starts prechill mode.
Unit returns to
normal on its own.

Defrost Test

Toggles on the
defrost cycle.

See

Note 2

Must press again to
turn heater off. See

Note 2.

Main Control Reset/Test Exit

Causes a system
reset and exits test
mode.

Содержание PGCS1NFXSS











































































Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды

GE Consumer & Industrial PGCS1NFXSS, Техническое обслуживание руководство

Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды