GE Consumer & Industrial PGCS1NFXSS Скачать руководство пользователя

Страница: 45 / 74

– 45 –

Icemaker Fill Tube Heater

The

ll tube heater is energized during the

defrost cycle when the defrost thermostat is
closed. Remove the evaporator cover to access
the icemaker

ll tube heater. (See

Evaporator

Disconnect the

ll tube heater wire harness. The

resistance of the

ll tube heater is approximately

2644

Return Duct Heaters

A return duct heater has been added to each of

the 2 fresh food compartment return air ducts. The
heaters prevent water from freezing and blocking
the air

ow in the ducts. Restricted ducts can cause

warm fresh food temperatures. (See

Airfl ow

Return Duct

Outlets

Return Duct Heaters Test

If open duct heaters are suspected, perform the
following:

With the over-temperature thermostat closed,

test for approximately 27

(the equivalent

resistance of this parallel circuit) between J9
and J7-9 .

For a resistance reading other than

approximately 27

, remove the evaporator

cover (See

Evaporator

.), disconnect the

ll tube

heater, and one lead from the defrost heater.
Insert a volt ohm meter into the

ll tube heater

receptacle. A reading of approximately 220

indicates both heaters are good.

Note:

The return duct heaters are integral to the

foamed in place internal ductwork of the refrigerator
and are not replaceable.

The heaters operate with 120 VAC and each heater
has an approximate resistance value of 440

The heaters are in a parallel circuit consisting of
2 duct heaters, icemaker

ll tube heater, and the

defrost heater. The line voltage wires of the duct
heaters and the

ll tube heater are connected to

the blue wire of the defrost heater. The neutral wires
of the heaters go through the over-temperature
thermostat. The 2 duct heaters and the

ll tube

heater are energized (along with the defrost heater)
during the defrost cycle when the over-temperature
thermostat is closed.

Содержание PGCS1NFXSS











































































Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды

GE Consumer & Industrial PGCS1NFXSS, Техническое обслуживание руководство

Результаты поиска

Содержание PGCS1NFXSS

Отзывы:

Похожие инструкции для PGCS1NFXSS

Бренды по названию

Популярные бренды