GCS CYSCAN Скачать руководство пользователя страница 4

Страница: 4 / 52

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

Troubleshooting .......................................... 28

For further assistance .............................................................................. 28

No communication between CyScan Console and the Sensor ........ 28

Sensor head does not rotate ......................................................... 28

Sensor rotates slowly ..................................................................... 29

System appears to be operational, however, the sensor
head is not levelling or rotating ..................................................... 29

System appears to be operational, however, no reflections
are displayed within CyScan Console ............................................. 29

System is operational but is not navigating .................................... 29

System navigating but no data is received at the DP system ........... 29

System appears to be operational, however, it is exhibiting
erratic behaviour with communications locking up occasionally ..... 29

System operates correctly but in cold weather loses targets. .......... 29

Alarm Codes ........................................................................................... 30

Fatal alarms - codes 2xxx ............................................................... 30

Errors - codes 3xxx ........................................................................ 30

Warnings - codes 4xxx .................................................................. 30

Information - codes 5xxx ............................................................... 30

CyScan Fuse Information ......................................................................... 31

Power Supply Unit Fuse ................................................................. 31

Controller Board Fuse .................................................................... 31

Appendices ................................................... 32

Appendix 1 - CyScan Sensor Connector Pin-outs ..................................... 32

Appendix 2 - CyScan Sensor Mounting Template ..................................... 33

Appendix 3 - CyScan PSU Mounting Template ......................................... 34

Appendix 4 - CyScan RS485 Data Converter Mounting Template ............. 35

Appendix 5 - Recommended Spares List .................................................. 36

Appendix 6 - Using CyScan Admin Console ............................................. 37

To start CyScan Admin Console ..................................................... 37

To exit CyScan Admin Console ...................................................... 37

CyScan Admin Console Quick Start ............................................... 38

Setting up the User Console Vessel Orientation ................... 39

Checking the Comms Port Settings ..................................... 40

Reinitialise the communications link .................................... 41

Enable Sensor Components ................................................ 42

Check Scanner Enabled ....................................................... 43

Check system supply voltages ............................................. 44

Mooring Point Reflectors - Installation and Definition ............................... 45

Reflector types .............................................................................. 45

Reflector Installation ..................................................................... 46

Defining Reflector Positions ........................................................... 47

Reflector Positioning Examples ...................................................... 48

Содержание CYSCAN





















































Результаты поиска

Содержание CYSCAN

Отзывы:

GCS CYSCAN, Руководство по установке и обслуживанию, Страница: 4 / 52

Результаты поиска

Содержание CYSCAN

Отзывы: