GCS CYSCAN Скачать руководство пользователя страница 3

Страница: 3 / 52

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

Contents

Introduction .................................................... 3
CyScan Installation ....................................... 4

Unpacking the CyScan System .................................................................. 4

Mounting the System Components ........................................................... 6

When mounting two CyScan sensors on the same vessel ....... 6

Wiring the CyScan System ......................................................................... 8

Power Supply Unit (PSU) ................................................................. 8

The Data Converter ....................................................................... 10

Notebook computer ...................................................................... 10

Connecting the CyScan Sensor ................................................................ 11

CyScan LED Indicators ............................................................................. 12

Correct startup indication .............................................................. 12

Error states and possible causes ..................................................... 12

Shutdown/suspend ....................................................................... 12

CyScan Removal .......................................... 13

Switching off the CyScan Console System ............................................... 13

Disconnecting the CyScan Sensor ............................................................ 14

Un-mounting the CyScan Sensor ............................................................. 14

Packing the CyScan System ..................................................................... 15

Maintenance and Servicing ....................... 17

Removing and fitting key components ..................................................... 17

Stage 1 - The Rotor Heatshield ...................................................... 17

Stage 2 - The Rotor ....................................................................... 18

Stage 3 - The Body Cover .............................................................. 19

Stage 4 - The Motor Gearbox ........................................................ 20

Stage 5 - The CPU Module ............................................................ 21

Stage 6 - The Controller Board ...................................................... 22

Stage 7 - The Yaw Gyro ................................................................ 23

Stage 8 - The Vertical Reference Unit (VRU) ................................... 24

Stage 9 - The Actuators ................................................................ 25

Cleaning the CyScan Sensor .................................................................... 27

To clean the casing and bellows: ................................................... 27

To clean the optical window: ......................................................... 27

To clean the targets: ...................................................................... 27

Greasing the Gearbox ............................................................................. 27

Содержание CYSCAN





















































Результаты поиска

Содержание CYSCAN

Отзывы:

GCS CYSCAN, Руководство по установке и обслуживанию, Страница: 3 / 52

Результаты поиска

Содержание CYSCAN

Отзывы: