manualshive.com logo in svg

GCS CYSCAN, Руководство по установке и обслуживанию, Страница: 27 / 52

Поделиться
Скачать
GCS CYSCAN Скачать руководство пользователя страница 27

25

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

Stage 9 - The Actuators

To remove an Actuator unit:

(applies equally to the Pitch and Roll Actuators)

1 Disconnect the ribbon cable connector at

the rear of the actuator circuit board.

2 Using a 4mm A/F hex key, remove the

two bolts at either end of the actua-
tor crosspiece.

3 Carefully rotate the large toothed

pulley of the actuator anti-clockwise
(as viewed from above) until it
releases from the lead screw shaft
that extends down into the base of
the sensor.

IMPORTANT: As you turn the large toothed pulley,
take care not to damage the encoder disc (the thin
circular metal plate with four slots cut through it).

Throughout the winding process, it may be necessary to
slant the body of the sensor into various positions to
accommodate the actuator and lead screw shaft within
the confines of the sensor frame.

4 When the lead screw shaft

releases from the actuator,
remove the actuator crosspiece
from the sensor frame.

5 To remove the actuator base, remove

the four M5 x 20 bolts from the two
pedestal bearings at either side of the
actuator base.

see next page for fitting instructions

Содержание CYSCAN





















































Отзывы:

Нет отзывов