GCS CYSCAN Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 52

GCS CYSCAN Скачать руководство пользователя страница 10

8

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

Wiring the CyScan System

The CyScan system introduces four main items to the vessel, these are:

• CyScan Sensor

• Power Supply Unit

• Data Converter

• CyScan Console Notebook Computer

The diagram below indicates the connections between the four items.

1

2

3

4

5

6

7

8

9

10

11

12

3

13

14

15

16

17

18

19

20

21

3

22

22

22

22

23

23

23

23

3

Console

DP

Power

2TX

2RX

1TX

1RX

PW

R

Power

CyScan

Sensor

Power

Supply

Unit

Data

Converter

DP Feed

Console Feed

To

DP Unit

Main

Power In

CyScan
Console
notebook
computer

Power Supply Unit (PSU)

The PSU is supplied with three flying leads, all of which attach to the connectors at the
Stern end of the sensor. Three M20 x 1.5 threaded holes (fitted with stopping plugs) are
provided to accommodate cable glands leading to/from:

• The vessel’s DP system

• The CyScan notebook computer (via the Data Converter)

• A suitable AC power feed

Inside, the PSU contains a row of industrial connectors to make the wiring process as
quick and flexible as possible. Each connector is numbered and the relevant signal con-
nections (with their connector number) are shown on the diagram (overleaf). The PSU
requires a supply of 90-264VAC at 5A.

«
...
8
9
10
11
12
...
»

Содержание CYSCAN





















































Отзывы:

Нет отзывов