GCS CYSCAN Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

GCS CYSCAN Скачать руководство пользователя страница 25

23

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

Stage 7 - The Yaw Gyro

To remove the Yaw Gyro:

1 Looking from the Starboard side of

the sensor locate the yaw gyro - a
small vertically mounted circuit
board. Using a 2.5mm A/F hex tool
to remove the two M3 x 16 screws
that secure the yaw gyro board to
the sensor frame (these are
normally hidden behind the
controller board).

2 Disconnect the ribbon cable

connector from the yaw gyro
board.

3 Lift out the yaw gyro unit.

To fit the Yaw Gyro:

1 Place the yaw gyro board into the

sensor frame adjacent to the pitch
actuator. The large rectangular
component (the gyro unit) should
be uppermost on the board.

2 Locate the ribbon cable leading

from the VRU board and attach it
to the connector situated towards
the bottom of the yaw gyro
assembly.

3 Insert two M3 x 16 screws through

the upper and lower frame bars
and into the corresponding
threaded holes of the yaw gyro
board. Using a 2.5mm A/F hex
tool, tighten both screws to
reasonable hand tightness.

«
...
23
24
25
26
27
...
»

Содержание CYSCAN





















































Отзывы:

Нет отзывов