GatesAir Intraplex NetXpress Скачать руководство пользователя страница 69

Страница: 69 / 163

4—System Configuration and Operation

Intraplex NetXpress IP Multiplexer

Version 3.05

GatesAir, Inc.

4-15

Intraplex Products

Figure 4-19. Networking | SNMP Configuration Page

Type the

SNMP

Read-Only

Community

name for read-only access.

Type the

SNMP

Read-Write

Community

name for read/write access.

Click

Submit

4.2.3.10 Configuration Backup/Restore

You can operate the NetXpress multiplexer without performing this procedure. However, we recommend
you save your configuration files.

Point to

System Cfg

and click

Configuration

Backup

(Figure 4-20).

Figure 4-20. System Cfg | Configuration Files Backup/Restore Page

Type the

Config

Backup

Server

address, the address of an available FTP server.

Type the

Config

Backup

Server

Directory

where the configuration files should be stored.

Type the

Username

Type the

Password

Click

Submit

to store these values.

Click

on the

Streams

table header to back up the configuration files to the server.

Содержание Intraplex NetXpress




































































































































































Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды

GatesAir Intraplex NetXpress, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды