GatesAir Intraplex NetXpress Скачать руководство пользователя страница 136

Страница: 136 / 163

Intraplex NetXpress IP Multiplexer

4—System Configuration and Operation

Version 3.05

4-82

GatesAir, Inc.

Intraplex Products

4.4.11.1 Sample Program Audio Module Configuration and Status

Figure 4-88. PT-353 Configuration Page

Alias Name:

Type a name to help identify the module type.

Shelf Address:

The IP address for the multiplexer shelf housing the module. This field is read-only.

Card Address:

SCB address assigned to the module. Each module must have a unique address. Valid

addresses are 1 through 36. This field is read-only.

TDM Bus:

The TDM bus identifier on which the channel module resides. This field is read-only.

Module Adapter:

The type of module adapter installed in the rear of the shelf.

Remote Control:

The desired operation for the module (

REMOTE

LOCAL

). This field is read-only.

Enable Module:

Select this check box to place the module in service. If left blank, the module remains

offline.

Module Configured:

Whether the module is properly configured. This field is read-only.

TDM Bus Configuration

●

Timeslot:

Click an up or down arrow to specify the desired starting time slot (1 to 24 in T1 system, 1

to 31 in E1 system).

●

TDM Bus:

Click either

Bus A

Bus B

on the list to indicate the current bus side.

●

Skip Timeslot 16:

Select this check box to set the module for use in an E1 (2MB) multiplexer set for

CAS signaling.

Audio Configuration

●

Bandwidth:

Click the audio sample rate bandwidth from the list (

32 ksps

44.1 ksps

48 ksps

●

Mode:

Click the mode (

Mono

Stereo

●

Turn Test Tone On:

(PT Modules Only)

Select this check box to enable a built-in +8dB test tone on

the active channels.

●

Use J.17 Emphasis:

Select this check box to enable emphasis on the outgoing signal in accordance

with ITU-T Recommendation J.17. If the transmitter module emphasis is enabled, the receiver
module de-emphasis must be enabled and vice versa.

Содержание Intraplex NetXpress




































































































































































Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды

GatesAir Intraplex NetXpress, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды