GatesAir Intraplex NetXpress Скачать руководство пользователя страница 79

Страница: 79 / 163

4—System Configuration and Operation

Intraplex NetXpress IP Multiplexer

Version 3.05

GatesAir, Inc.

4-25

Intraplex Products

SNTP Server Status:

Indicates whether the SNTP Server was reached at the specified IP address.

Reset:

Click this button to clear all recent configuration entries and/or changes and return to previous

values.

Submit:

Click this button to apply setup changes.

4.4.3.2 Interfaces Table

Use the

Interfaces

Table

to view NIM interface statistics. Point to

System

Cfg

and click

Interfaces

Once the

Interface

Table

appears, click

to view statistics for the interface that you selected. Figure

4-29 shows information for the WAN interface.

Note:

If WAN redundancy is enabled, the

Operational

State

and

Administrative

State

columns for

the

LAN

interface are

Redundant

Figure 4-29. Interfaces Table

Refresh:

Click this button to refresh this page in your browser.

Interface:

Identifies the NetXpress IP interface.

Type:

Interface type (from MIB-II specification).

Speed/Duplex:

Interface speed/Duplex state.

Operational State:

Current operational state of the interface.

Administrative State:

Current administrative state, which is user defined as either

service

out

service

Содержание Intraplex NetXpress




































































































































































Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды

GatesAir Intraplex NetXpress, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды