GatesAir Intraplex NetXpress Скачать руководство пользователя страница 118

Страница: 118 / 163

Intraplex NetXpress IP Multiplexer

4—System Configuration and Operation

Version 3.05

4-64

GatesAir, Inc.

Intraplex Products

Near End:

The statistics for the closer end of the E1 port.

Far End:

The statistics for the farther end of the E1 port.

Current Interval Statistics:

The statistics of the interval currently.

Cumulative Interval Statistics:

An average of interval statistics.

ES:

Errored Seconds; the number of seconds in which at least one code violation (CV) was detected on

the circuit.

SES:

Severely Errored Seconds. An SES is a second in which a severe number of errors are detected over

the circuit.

SEFS:

Severely Errored Framed Seconds; a count of the number of seconds during which, at any point,

the Severely Errored Framing (SEF) defect was present.

UAS:

Unavailable Seconds; a count of one-second intervals during which service is unavailable.

CSS:

Controlled Slip Seconds; a count of one-second intervals of one or more controlled slips. A

controlled slip is the occurrence of a replication or deletion of a T1 frame by the receiving terminal.

PCV:

Path Coding Violations; the number of code violations per second within the path.

LES:

Line Errored Seconds; a count of one-second intervals in which one or more LCV error events were

detected.

BES:

Bursty Errored Seconds; a count of one-second intervals greater than one and less than 320 CRC

error events.

LCV:

Line Code Violations; the number of code violations per second within the line.

Interval:

The specific interval to which these statistics correspond.

4.4.6.4 SNMP Statistics

Select

SNMP

(Simple Network Management Protocol) from the

Performance

menu to view SNMP

message information on the

SNMP Statistics

page for the IP multiplexer (Figure 4-72). These are total

statistics since the system last rebooted. All of the statistics are totals since the system last rebooted.

Содержание Intraplex NetXpress




































































































































































Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды

GatesAir Intraplex NetXpress, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды