GatesAir Intraplex NetXpress Скачать руководство пользователя страница 140

Страница: 140 / 163

Intraplex NetXpress IP Multiplexer

4—System Configuration and Operation

Version 3.05

4-86

GatesAir, Inc.

Intraplex Products

receive side data and sends it to the user as usual but also loops that data to the transmit side of the
module, processes it and returns the data to the originating module.

Refresh:

Click this button to refresh the browser.

Submit:

Click this button to apply the configuration values entered on this page.

Reset:

Click this button to change page fields back to the original values.

Previous Card:

Click this button to view configuration and status pages for the module on the immediate

left of this module.

Next Card:

Click this button to view configuration and status pages for the module on the immediate

right of this module.

Figure 4-91. VF-25E Status Page

The

Status

page fields are read-only; you cannot change any values on this page.

Alias Name:

The name you specify to help identify the module type.

Shelf Address:

The IP address for the multiplexer shelf housing the module.

Card Address:

The SCB address assigned to the module. Each module must have a unique address.

Valid addresses are 1 through 36.

TDM Bus:

The TDM bus on which the channel module resides.

Module Adapter:

The type of module adapter installed in the rear of the shelf.

Remote Control:

The desired operation for the module (

REMOTE

LOCAL

Enable Module:

Whether the module is in service or offline.

Module Configured:

Whether the module is properly configured.

In Service:

Whether the module is in service (green) or out of service gray).

Alarm:

If there is an active alarm (red) or alert (yellow) on the module.

Refresh:

Click

to refresh the browser manually or click an option to set the browser to refresh

automatically at 5 second, 10 second, or 30 second intervals.

Содержание Intraplex NetXpress




































































































































































Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды

GatesAir Intraplex NetXpress, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex NetXpress

Отзывы:

Похожие инструкции для Intraplex NetXpress

Бренды по названию

Популярные бренды