background image

No header here 

GatesAir, Inc. 

 

6-1 

Intraplex Products 

Section 6 – Specifications 

6.1  Detailed Specifications 

Ethernet Data Rate 

10/100 BASE-T (10 or 100 Mbps) 
Full duplex 
Auto-negotiation with network 

Ethernet Connector 

Port 1 – Management LAN- Female RJ-45 
Port 2 – WAN- Female RJ-45 
Port 3 – LAN- Female RJ-45 

T1/E1 Data Rate 

T1: 1.544Mbps 
E1: 2.048Mbps 

T1/E1 Connector 

2 – Female RJ-45 

T1 Specifications 

 

Physical Interface        

RJ-48C: 8-pin Modular 

Compatibility 

ATT 54016, ATT 62411, and ANSI T1.403 

Line Rate 

1.544 Mbps +/- 30 PPM, using internal timing 

Line Code 

AMI or B8ZS 

Line Build Out 

0, -7.5, -15, or -22 dB 

Line Input Impedance 

100 Ohms 

Framing 

D4 (SF) or ESF 

Robust Framing 

Mean time to lose frame at 10-3 BER: 
Greater than 450 hours for ESF 
Greater than 225 hours for SF 

Performance Monitoring 

ANSI T1.231, ANSI T1.403 PRM, and ATT 54016 

Compliance 

FCC Part 68 
Industry Canada CS-03 

E1 Specifications 

 

Physical Interface        

RJ-48C: 8-pin Modular 

Compatibility 

ITU G.703, G.704, G.706, G.732, G.736, and G.823 

Line Rate 

2.048 Mbps +/- 30 PPM, using internal timing 

Line Code 

AMI or HDB3 

Line Input Impedance 

120 Ohms 

Framing 

CAS (Channel Associated Signaling) or CCS (Common Channel Signaling) 

Robust Framing 

Mean time to lose frame at 10-3 BER greater than 20 hours 

Performance Monitoring 

G.826 

Compliance 

ETSI TBR12 and TBR13 

Содержание Intraplex NetXpress




































































































































































Отзывы: