GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 63 / 143

SERVICE WORK ON THE CHASSIS 11

11.26

Installing the air filter

H02459-01

Main work

–

Mount the clean air filter on the air filter support.

–

Grease the air filter in area

Long-life grease (

p. 132)

A00784-10

–

Insert air filter and position retaining pin

in bushing

The air filter is correctly positioned.

–

Insert retaining tab

Retaining pin

is secured by retaining tab

Info

If the air filter is not mounted correctly, dust and dirt may
enter the engine and result in damage.

Finishing work

–

Install the air filter box cover. (

p. 58)

11.27

Preparing air filter box cover for securing

Preparatory work

–

Remove the air filter box cover. (

p. 57)

F03206-10

Main work

–

Drill a hole at marking

Guideline

Diameter

6 mm (0.24 in)

Finishing work

–

Install the air filter box cover. (

p. 58)

11.28

Removing the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды