GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 69 / 143

SERVICE WORK ON THE CHASSIS 11

A00787-11

–

Plug in connector

for the fuel pump.

–

Remove the wash cap set. Clean the quick release coupling thor-
oughly with compressed air.

Info

Under no circumstances should dirt enter into the fuel
line. Dirt in the fuel line clogs the injection valve!

–

Spray silicone spray onto a lint-free cleaning cloth and lightly
lubricate the O-ring of the quick-release coupling.

Silicone spray (

p. 132)

–

Join quick release coupling

Info

Route the cable and fuel line at a safe distance from the
exhaust system.

Finishing work

–

Mount the seat. (

p. 57)

11.33

Checking for chain dirt accumulation

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 67)

11.34

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the appli-
cable regulations.

Info

The service life of the chain depends largely on its maintenance.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды