GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 66 / 143

11 SERVICE WORK ON THE CHASSIS

A00785-10

Main work

(MC)

–

Unplug connector

of the fuel pump.

–

Clean quick release coupling

thoroughly with compressed

air.

Info

Under no circumstances should dirt enter into the fuel
line. Dirt in the fuel line clogs the injection valve!

A00820-10

–

Disconnect the quick release coupling.

Info

Remaining fuel may flow out of the fuel hose.

–

Mount wash cap set

Wash cap set (81212016100)

–

Pull the fuel tank breather hose off the fuel tank lid.

A00786-10

–

Remove screw

with the rubber bushing.

A00787-10

(EX)

–

Unplug connector

of the fuel pump.

–

Clean quick release coupling

thoroughly with compressed

air.

Info

Under no circumstances should dirt enter into the fuel
line. Dirt in the fuel line clogs the injection valve!

A00820-10

–

Disconnect the quick release coupling.

Info

Remaining fuel may flow out of the fuel hose.

–

Mount wash cap set

Wash cap set (81212016100)

–

Pull the fuel tank breather hose off the fuel tank lid.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды