GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 95 / 143

WHEELS, TIRES 13

13.7

Checking the spoke tension

Warning

Danger of accidents

Incorrectly tensioned spokes impair the handling characteristic and result in secondary dam-

age.
The spokes break due to being overloaded if they are too tightly tensioned. If the tension in the spokes is too low,
then lateral and radial run-out will form in the wheel. Other spokes will become looser as a result.

–

Check spoke tension regularly, and in particular on a new vehicle. (Your authorized GASGAS Motorcycles work-
shop will be glad to help.)

400694-01

–

Strike each spoke briefly using a screwdriver blade.

Info

The frequency of the sound depends on the spoke length
and spoke diameter.

If spokes of the same length and diameter vibrate with a
different tone, this is an indication that the spoke tensions
differ.

You should hear a high note.

» If the spoke tension differs:

–

Correct the spoke tension.

–

Check the spoke torque.
Guideline

Spoke nipple, front
wheel

M4.5

6 Nm (4.4 lbf ft)

Spoke nipple, rear
wheel

M4.5

6 Nm (4.4 lbf ft)

Torque wrench kit (58429094000)

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды