GAS GAS MC 250F 2022 Скачать руководство пользователя | Manualshive

Страница: 85 / 143

background image

BRAKE SYSTEM 12

83

12.9

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

A00831-10

–

Detach spring

1

.

–

Loosen nut

4

and, with push rod

5

, turn it back until you have

maximum free travel.

–

To adjust the basic position of the foot brake lever to individual
requirements, loosen nut

2

and turn screw

3

accordingly.

Info

The range of adjustment is limited.

–

Turn push rod

5

accordingly until you have free travel

A

. If nec-

essary, adjust the basic position of the foot brake lever.
Guideline

Free travel at foot brake lever

3 … 5 mm (0.12 … 0.2 in)

–

Hold push rod

5

and tighten nut

4

.

Guideline

Remaining nuts, chas-
sis

M6

10 Nm (7.4 lbf ft)

–

Hold screw

3

and tighten nut

2

.

Guideline

Nut, foot brake lever
stop

M8

20 Nm (14.8 lbf ft)

–

Attach spring

1

.

12.10

Checking the rear brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is leaking or the
brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized GAS-
GAS Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule.
(Your authorized GASGAS Motorcycles workshop will be glad to help.)

Preparatory work

–

Check the brake linings of the rear brake. (

«
...
83
84
85
86
87
...
»

Содержание MC 250F 2022
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC 250F 2022

Бренд: ZARD Страницы: 2

Бренд: N-Com Страницы: 2

Бренд: National Cycle Страницы: 5

Бренд: Biltema Страницы: 2

Бренд: Yamaha Страницы: 39

Roadliner XV1900AV

Бренд: Yamaha Страницы: 86

ROADLINER XV19C

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 70

Road Star XV1600AT 2004

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 72

Road Star XV17ASX

Бренд: Yamaha Страницы: 110

Road Star XV1600A 2000

Бренд: Yamaha Страницы: 103

Road Star XV16AMC

Бренд: Yamaha Страницы: 110

ROAD STAN XV17AC

Бренд: Yamaha Страницы: 105

Бренд: Yamaha Страницы: 70

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды