GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 92 / 143

13 WHEELS, TIRES

A00841-10

Main work

–

Manually press the brake caliper toward the brake disc to push back
the brake piston.

Info

Make sure that you do not press the brake caliper against
the spokes when pushing back the brake piston.

–

Remove nut

–

Take off chain adjuster

. Pull out wheel spindle

far enough to

allow the rear wheel to be pushed forward.

–

Push the rear wheel forward as far as possible. Remove the chain
from the rear sprocket.

Info

Cover the components to protect them against damage.

Warning

Danger of accidents

Damaged brake discs reduce the

braking effect.

–

Always lay the wheel down in such a way that the brake
disc is not damaged.

–

Hold the rear wheel and remove the wheel spindle. Take the rear
wheel out of the link fork.

Info

Do not operate the foot brake lever when the rear wheel is
removed.

H03002-10

–

Remove spacers

13.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды