GAS GAS MC 250F 2022 Скачать руководство пользователя

Страница: 43 / 143

TUNING THE CHASSIS 10

The fork airpump indicator switches off automatically after
80 seconds.

–

Mount the protection cap.

Info

Only mount the protection cap by hand.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 44)

10.14

Adjusting the compression damping of the fork

Info

The hydraulic compression damping determines the fork suspension behavior.

A00776-10

–

Turn adjuster

clockwise all the way to the stop.

Info

Adjuster

is located at the upper end of the right fork leg.

–

Turn counterclockwise by the number of clicks corresponding to the
fork type.
Guideline

Compression damping (MC)

Comfort

17 clicks

Standard

12 clicks

Sport

7 clicks

Compression damping (EX)

Comfort

17 clicks

Standard

12 clicks

Sport

7 clicks

Info

Turn clockwise to increase damping; turn counterclockwise
to reduce damping during compression.

10.15

Adjusting the rebound damping of the fork

Info

The hydraulic rebound damping determines the fork suspension behavior.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды