GAS GAS MC 250F 2022 страница 60 Скачать руководство пользователя

Страница: 60 / 143

11 SERVICE WORK ON THE CHASSIS

A00782-11

–

Pull off the air filter box cover in area

sideways and take off

toward the front.

A00819-10

Condition

The air filter box cover is not secured.

–

Pull off the air filter box cover in area

sideways and take off

toward the front.

11.23

Installing the air filter box cover

A00782-12

(MC)

Condition

The air filter box cover is secured.

–

Insert the air filter box cover in area

and clip it into

area

Info

An air filter box cover with openings for greater air-
flow and a more direct response is included.

A00782-10

–

Mount and tighten screw

Guideline

Screw, air filter box
cover

EJOT PT

K60x20-Z

3 Nm (2.2 lbf ft)

–

Mount the seat. (

p. 57)

A00819-11

Condition

The air filter box cover is not secured.

–

Insert the air filter box cover in area

and clip it into

area

Info

An air filter box cover with openings for greater air-
flow and a more direct response is included.

Содержание MC 250F 2022
















































































































































Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 250F 2022, Руководство пользователя

Результаты поиска

Содержание MC 250F 2022

Отзывы:

Похожие инструкции для MC 250F 2022

Бренды по названию

Популярные бренды