manualshive.com logo in svg

GARDINER TECHNOLOGY Gardtec 800, Руководство по установке

Поделиться
Скачать
GARDINER TECHNOLOGY Gardtec 800 Скачать руководство пользователя страница 41

Page 

79

Page 

78

GARDTEC 

800 Series

Miscellaneous

Appendix 1

Using Point ID 

The ProDigi Communicator or Gardtec 

800 Series 

Modem from Gardiner Technology

may, if required be used to allow Point ID communication with the Gardtec 840. When
used in this mode the ProDigi/Modem will use the Ademco Point ID Protocol.

Point ID allows for the transmission of zone and detector types to be transmitted along
with the alarm information. This qualifies as sequential verification as recommended by
the 1995 ACPO policy. 

To use Point ID the ProDigi/Modem should be connected to the Gardtec 

840  

via the

serial lead that is supplied with it (this is shown in Fig 16 on page 25). 

To use the communicator in Point ID mode and program the relevant functions, the
control panel needs to be told that it is to use the ProDigi as a Point ID communicator.
This is done via option 34 in the engineer options (Digicom Type), which should be
changed to:-

Digicom Type.....
= Point ID or Mod+PID for the Modem

If using an LED type keypad to select Point ID:-

With the display showing E- press 34 followed by YES

Then press NO 03 (or 04 for Modem) followed by YES

It should be noted that although you are able to turn on the Point ID function via an
LED keypad you will not be able to program the Digicom functions unless you are
working via an LCD keypad. This allows for a pre-programmed ProDigi to be fitted onto
an existing system with LED only keypads.

When using the ProDigi or Modem with the Gardtec 

800 Series 

control panel you

will be able to use the ProDigi as a Point ID communicator or fast format
communicator. It is not possible to use both formats at the same time.

GARDTEC 

800 Series

Miscellaneous

Engineer Reset After An Alarm

If a system is programmed for engineer reset it will be necessary for the engineer to
attend the system. After the engineer has confirmed the integrity system the system
should be reset as follows:-

1)

After the system has been Unset, enter the
engineer code, the display will show:-

2)

Press NO, the display will show:-

3)

Press YES, the display will show:-

4)

Enter the engineer code again to abort the
setting, the display will show:-

5)

The system is now Unset.

< < < < UN-SET > > > >
01 Jan 00: 00: 01

Do you want to . . 
Use ENGNR.  Mode ?

Do you want to . . 
SET the System  ?

Exit Now !  1 2 3 C
All Zones On    28

4344R12.qxd  03/09/99 11:09  Page 78

Содержание Gardtec 800












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды