Gardenline GLPC 41 Скачать руководство пользователя страница 53

Страница: 53 / 72

AFTER SALES SUPPORT

0151 649 1500

1890 946244

www.einhell.co.uk

41cc Petrol Chainsaw – GLPC 41

Maintenance and servicing

CAUTION!

Activate the chain brake slowly and deliberately. Keep the

chain from touching anything; don't let the saw tip forward.

6. Chain should stop abruptly. When it does, immediately release the throttle trigger.

CAUTION!

If chain does not stop, turn engine off and take your unit to

the nearest Authorized Service Centre for service.

7. If the chain brake functions properly, turn the engine off and return the chain brake to

the

DISENGAGED position.

Air Filter

NOTICE!

Never operate the saw without the air filter. Dust and dirt will

be drawn into the engine and damage it. Keep the air filter

clean! The air filter must be cleaned or replaced after every

20 hours of service.

Maintenance and ordering of spare parts

Always switch off the equipment and disconnect the spark plug boot (Fig. 4/Item 23)

before carrying out any maintenance work.

Содержание GLPC 41









































































Результаты поиска

Содержание GLPC 41

Отзывы:

Похожие инструкции для GLPC 41

Бренды по названию

Популярные бренды

Gardenline GLPC 41, Общее руководство пользователя

Результаты поиска

Содержание GLPC 41

Отзывы:

Похожие инструкции для GLPC 41

Бренды по названию

Популярные бренды